Pocket Dissolved oxygen tester LPKDO-A10 is equipped with polarographic sensor to measure dissolved oxygen content. The system menu of dissolved oxygen meter can set 6 parameters which includes the number of calibration points, temperature units etc. It can measure the dissolved oxygen content present in water, waste water, other liquids & solutions.
| Dissolved oxygen range | 0.0 to 20.0 mg/L (or ppm) |
|---|---|
| Dissolved oxygen accuracy | ± 0.5 mg/L |
| % of saturation of oxygen | 0.0 to 200.0% |
| Sensor type | Polarographic dissolved oxygen probe |
| % Saturation of oxygen accuracy | ± 10 % F.S. |
| Temperature compensation range | 0 °C to 40 °C, 32 °F to 104 °F |
| Barometric pressure correction | 60.0 to 112.5 kPa, 450 to 850 mmHg |
| Salinity correction | 0 - 35 g/L |
| Data hold function | Manual or automatic |
| Power off | Manual or automatic (8 minute after last key is pressed) |
| Reset function | Yes |
| Connector | 6 pin mini plug |
| Battery life | Approximately 150 hours |
| Dimension (L × Dia.) | 175 × 40 mm |
| Weight | 100 g |
Pocket Dissolved oxygen tester has applications in water & waste water management industry, aquarium, surface ground water, etc. to detect content of dissolved oxygen.
Labtron benchtop meters are easy to use. The LCD display, manual or automatic mode of calibration, universal connector and other features are included in this range to produce accurate, reliable results. It consist of benchtop meter for measuring pH, conductivity, dissolved oxygen content, Ion concentration, water hardness level. These meters are suitable for simple to complex applications in water quality testing, research and analysis etc.
| pH range | -2.00 to 20.00 pH |
| pH Accuracy | ± 0.002 pH |
| pH Resolution | 0.1/0.01/0.001 pH, selectable |
| pH Calibration Points | 1 to 5 Points |
| pH Buffer Solutions | USA (pH 4.0/7.00/10.01) or NIST (pH 4.01/6.86/9.18) or DIN buffers |
| mV Range | -1999.9 to 1999.9 mV |
| mV Accuracy | ± 0.2 mV |
| mV Resolution | 0.1/1 mV, selectable |
| mV Calibration Points | 1 Point |
| Conductivity Range | 0.01 to 20.00, 200.0, 2000 µS/cm, 20.00, 200.0 mS/cm |
| Conductivity Accuracy | ± 0.5% F.S. |
| Conductivity Resolution | 0.01/0.1/1 |
| Conductivity Calibration Points | 1 to 5 Points |
| Conductivity Solutions | 10, 84, 1413 µS/cm, 12.88, 111.8 mS/ cm |
| Conductivity Temperature coefficient | 0.0 to 10.0 %/°C |
| Compensation mode | Linear or Pure Water |
| Cell Constant | K=0.1, 1, 10 or Custom |
| Reference temperature | 20 or 25°C |
| Dissolved Oxygen Range | 0.00 to 20.00 mg/ L |
| Dissolved Oxygen Accuracy | ± 0.2 mg/ L |
| Dissolved Oxygen Resolution | 0.1/ 0.01 mg/ L, selectable |
| Dissolved Oxygen Calibration Points | 1 or 2 Points |
| % Saturation Range | 0.0 to 200.0 % with ± 2 % accuracy |
| Pressure correction | 60 to 112.5 kPa, 450 to 850 mmHg |
| Salinity correction | 0 to 50 g/ L |
| pH range | -2.00 to 20.00 pH |
| pH Accuracy | ± 0.002 pH |
| pH Resolution | 0.1/0.01/0.001 pH, selectable |
| pH Calibration Points | 1 to 5 Points |
| pH Buffer Solutions | USA (pH 4.0/7.00/10.01) or NIST (pH 4.01/6.86/9.18) or DIN buffers |
| mV Range | -1999.9 to 1999.9 mV |
| mV Accuracy | ± 0.2 mV |
| mV Resolution | 0.1/1 mV, selectable |
| mV Calibration Points | 1 Point |
| Conductivity Range | 0.01 to 20.00, 200.0, 2000 µS/cm, 20.00, 200.0 mS/cm |
| Conductivity Accuracy | ± 0.5% F.S. |
| Conductivity Resolution | 0.01/0.1/1 |
| Conductivity Calibration Points | 1 to 5 Points |
| Conductivity Solutions | 10, 84, 1413 µS/cm, 12.88, 111.8 mS/ cm |
| Conductivity Temperature coefficient | 0.0 to 10.0 %/°C |
| Compensation mode | Linear or Pure Water |
| Cell Constant | K=0.1, 1, 10 or Custom |
| Reference temperature | 20 or 25°C |
| TDS Range | 0 to 10.00, 100.0, 1000 ppm, 10.00, 100 ppt (Max. 200 ppt) |
| TDS Accuracy | ± 1 % F.S. |
| TDS Factor | 0.1 to 1.0 (default 0.5) |
| pH range | -2.00 to 20.00 pH |
| pH Accuracy | ± 0.002 pH |
| pH Resolution | 0.1/0.01/0.001 pH, selectable |
| pH Calibration Points | 1 to 5 Points |
| pH Buffer Solutions | USA (pH 4.0/7.00/10.01) or NIST (pH 4.01/6.86/9.18) or DIN buffers |
| mV Range | -1999.9 to 1999.9 mV |
| mV Accuracy | ± 0.2 mV |
| mV Resolution | 0.1/1 mV, selectable |
| mV Calibration Points | 1 Point |
| Conductivity Range | 0.01 to 20.00, 200.0, 2000 µS/cm, 20.00, 200.0 mS/cm |
| Conductivity Accuracy | ± 0.5% F.S. |
| Conductivity Resolution | 0.01/0.1/1 |
| Conductivity Calibration Points | 1 to 5 Points |
| Conductivity Solutions | 10, 84, 1413 µS/cm, 12.88, 111.8 mS/ cm |
| Conductivity Temperature coefficient | 0.0 to 10.0 %/°C |
| Compensation mode | Linear or Pure Water |
| Cell Constant | K=0.1, 1, 10 or Custom |
| Reference temperature | 20 or 25°C |
| TDS Range | 0 to 10.00, 100.0, 1000 ppm, 10.00, 100 ppt (Max. 200 ppt) |
| TDS Accuracy | ± 1 % F.S. |
| TDS Factor | 0.1 to 1.0 (default 0.5) |